RUS

Sealed universal cable closures MGU-RWD

The sealed universal closures MGU-RWD are designed to replace UKM and UPM closures and are used cable stripping and connecting them to track circuits.

Technical performance

The closures have welded steel casing made of sheet metal, with powder-coated casing and cover, symmetrical connection of safety pipes and flanges (depending on the closure type). Along the perimeter of the cover there is a groove in which a seal made of porous rubber is inserted, which protects from ingress of dust and moisture.

The required number of bus terminals is installed inside the case. The closures are made in a climatic design UHL of the category I in accordance with GOST15150-69 for operation outdoors in areas with temperate and cold climate. According to the degree of protection against electric shock the closures belong to class 01 in accordance with GOST 12.2.007.0-75.

Design features

  • A transparent “pocket” is installed on the cover of the closure, designed to protect and store documentation (diagram, passport, etc.);

  • Reduced weight due to the use of sheet metal with a thickness of 2 mm, while the design is not inferior in strength to cast iron;

  • Improvement of sealing due to a porous rubber sealant; special mastic for sealing the cable glands also included;

  • An additional cable fixing device is used, which reduces installation time and increases reliability (excluding damage to the cable at the entrance point);

  • Applied vandal-proof cover locks (opening with a special pentagon wrench);

  • Anti-corrosion coating;

  • To protect the cables from mechanical damage, protective tubes are included in the delivery package;

  • For installation of the closure and protection of cables against mechanical damage, a protective tube with a base is included in the delivery package;

  • The cover is at the same time the closure body, opening which provides convenient access for working with the cable;

  • The conductors are connected with bus terminals, which allows to avoid twisting the conductor into the ring during installation, thereby reducing the likelihood of the conductor breaking during operation and reducing the installation time.

Ordering table

Name
Dimensions* (LхWхH), mm
Weight, kg
Number of bus terminals
Design features**
Closure analogue
Minimum lot to order, pcs.
Closure МГУ-2-RWD
260х245х595
8,6
2
- one inlet;
- one protective tube with a base.
МГУ-2
15
Closure МГУ-14-RWD 260х245х595
10,2
14
- two inlets;
- one protective tube with a base;
- one pipe for connection to a traffic light.
УКМ-12-I
УКМ-12-II
УКМ-12-III
УКМ-12-IV
МГУ-14-I
МГУ-14ШК-II
МГУ-14-III
МГУ-14ШК-III
42
Closure МГУ-28-RWD 320х260х595
13,1
28
- three inlets;
- one protective tube with a base;
- one joining pipe for connection to a traffic light.
УПМ-24-I
УПМ-24-II
УПМ-24-III
МГУ-28-I
МГУ-28ШК-I
МГУ-28-II
МГУ-28ШК-II
МГУ-28-III
МГУ-28ШК-III
22
Closure МГУ-28-IV-RWD 320х260х595
13,1
28
- three inlets;
- one protective tube with a base;
- one protective tube;
- one joining pipe for connection to a traffic light;
- one hose for the electric drive.
УПМ-24-IV
МГУ-28-IV
МГУ-28ШК-IV
22
Closure МГУ-28-V-RWD 380х275х595
19,8
28
- five inlets;
- one protective tube with a base;
- four protective tubes.
РМ4-28
МГУ-28-V
МГУ-28ШК-V
24

* Closure dimensions are specified for packaged form.

** Additionally, all closures are completed with cable fastener assemblies, beacon fastening bracket, wrench, cable ties, insulated screwdriver, joint paste.

Note: fittings for mounting on a mast must be ordered separately.

Order