RUS

High traffic light heads TLM-RWD

The high traffic light heads are designed for installation on railways of any purpose and serve to ensure traffic safety, as well as to organize the movement of trains and switching operations.

Technical performance

The high traffic light heads are a welded steel structure with a back plate, visors and LED modules MM-RWD installed in them with a light output diameter of 209±1 mm.

Installation is made on standard brackets for metal or reinforced concrete masts. The back plate, made of solid sheet metal with bends along the contour, which increases the rigidity of the structure, is installed at the installation site. The visors are mounted after installing the back plate, through it to the body of the traffic light head, which increases their resistance to wind loads. The visor length is 500 mm. The high traffic light heads are made in a climatic design UHL of the category I in accordance with GOST15150-69 for operation outdoors in areas with temperate and cold climate. By the method of protecting a person from electric shock, products belong to class 0 according to GOST IEC 61140. Degree of protection against external influences IP54 in accordance with GOST 14254-96.

Design features

  • One common door for all signals for opening convenience;

  • All fasteners are located inside the body, which protects them from environmental influences (rust, dirt, etc.) and allows the traffic light to be serviced from the side of the open cover from the ladder;

  • The assembly for mounting on a support is compatible with previous models, so its alteration is not required;

  • No injection method drawbacks (air pockets, notches, etc.);

  • No non-ferrous metals;

  • Maintainability;

  • Vandal-proof design;

  • Anti-corrosion coating;

  • There is a possibility to install lens sets with incandescent lamps on the outside of the head;

  • Power supply of the module from an AC or DC source:
    Rated voltage 11.5V AC (supply voltage range 9V-12V);
    Rated voltage 12V DC (supply voltage range 10V-14V);

  • Energy saving — maximum power consumption of the module is 15 W;

  • Elimination of false traffic signals due to reflection of sunlight or spotlights (“phantom (reflective) effect”) due to the absence of filters;

  • The electronic circuit of the light source allows to compensate for temperature effects and voltage changes, ensuring the constancy of light intensity;

  • The LED module provides the intensity of wrong side failures of no more than 2.4*10-10 h-1;

  • The design and photometric characteristics of the installed LED module comply with GOST R 56057-2014;

  • The maximum cable line distance when connected is no more than 3 km;

  • The “day-night” mode is implemented.

Ordering table

Name*
Head dimensions (HхWхD), mm
Back plate dimensions, mm
Weight, min., kg
Scope of supply**
Minimum lot to order
High traffic light head TLM-1-X-RWD
277х300х150
440х440
10,5
- body;
- one LED module;
- one visor;
- back plate;
- armored hose;
- wrench.
24
High traffic light head TLM-2-XX-RWD
797х300х150
814х604
22,8
- body;
- two LED modules;
- two visors;
- back plate;
- armored hose;
- wrench.
20
High traffic light head TLM-3-XXX-RWD
1021х300х150
1104х604
29,3
- body;
- three LED modules;
- three visors;
- back plate;
- armored hose;
- wrench.
21

* X – color names are indicated in order from top to bottom, where: R – red, Y – yellow, G – green, B – blue, W – moon-white.

** A gland is put into each kit to connect the armored hose to the mast (for cable entry).

Sample name for ordering: High traffic light head TLM-2-GR-RWD is a head of a two-aspect high traffic light with green and red light.

Note: brackets for mounting heads to the mast (upper and lower), ladders (folding, inclined), lettering plates, lettering plate fixture, transformer boxes, couplings and fitting for attaching to the mast are ordered separately.

Order